Binatone ADVENTURER 100 User Manual download pdf (Page 2)

To clean your PMR watch, use a soft cloth dampened with water. Do

not use cleaners or solvent, which may cause damage which may

not covered by guarantee.

5. Cleaning and care

Operating frequency 446.00625 to 446.09375 MHz(eight channels)

Channel spacing 12.5 KHz Output power 0.5 W

6. Technical specification

Channel Frequency(MHz) Channel Frequency(MHz)

1 446.00625

2 446.01875

3 446.03125

4 446.04375

5 446.05625

6 446.06875

7 446.08125

8 446.09375

(CTCSS - Continuous Tone Coded Squelch System)

Interference Elimination Codes

Code Frequency(Hz)

1 67. 0

Code Frequency(Hz)

2 71. 9

3 74. 4

4 77. 0

5 79. 7

6 82. 5

7 85. 4

8 88. 5

9 91. 5

10 94.8

11 97.4

12 100.0

13 103.5

14 107.2

15 110.9

16 114.8

17 118.8

18 123.0

19 127.3

20 131 .8

21 136 .5

22 141 .3

23 146 .2

24 151 .4

25 156 .7

26 162 .2

27 167 .9

28 173 .8

29 179 .9

30 186 .2

31 192 .8

32 203 .5

33 210 .7

34 218 .1

35 225 .7

36 233 .6

37 241 .8

38 250 .3

Problem Possible cause solution

No power Battery is low or not fitted correctly check;

PMR is not switched on check

Battery is low or not fitted correctly

Other user is not within range check

PMR are not tuned to the same channel

check

Noisy reception is more likely when using high

numbered sub-channels try using a lower-

numbered sub-channel,agreeing it with the rest

of your group first

Volume level is too low increase the volume

Speak in a normal voice,5-8cm(2-3 inches )

away from the microphone

Local conditions are impairing reception move

to a different location. away from obstructions

and as high as possible

Other user is not transmitting check

Other user is too close check

There's interference from other users on the same

channel agree to use a different channel

Cannot change PMR is locked check

channels Battery is low or not fitted correctly

In VOX mode, Background noise is high move to a quieter

the handset place

transmits all VOX sensitivity is too high set it to a lower

the time level

In VOX mode, VOX sensitivity is too low set it to a higher

the handset level

doesn't transmit Speak in a louder voice, nearer to the

microphone

8. Troubleshooting

weak reception/

no reception/

noisy reception

Cannot charge Make sure the mains power lead is firmly plugged

The batteries into the charger jack.

Make sure the mains power adapter is plugged in,

and that mains power is switched on at the socket.

Use only 3.6V Ni-MH batteries, as supplied with

the unit. You may need to recharge the battery pack

after many hours of use.

2 Call our Service Department on 0845 345 9677 and ask for a

quotation of the repair charge and details of where to send your

Adventurer3 for repair.

3 Return your Adventure to the address given by the Service

Department, making sure you include your name and address, and

a cheque or postal order for the value of the repair charge.

This does not affect your statutory rights.

Repair after the Guarantee has expired

If the unit is no longer under Guarantee, first follow steps 1 as for

repair under Guarantee. Then...

Binatone Telecom plc operates a policy of continuous product improve-

ment,and so reserves the right to make changes to the product and

functions without notice.

Select the desired channel by pressing UP or Down button.

Press MENU button once to change the CTCSS code.

Press UP or Down button to select the desired CTCSS code.

Press TALK button to confirm the setting.

The display switches backwards and forwards between the two

channels. If handset detects a signal on either channel, it will stop

and receive it. As long as the unit is in Dual watch mode, DCM is

shown steadily on the display.

To end the Dual Watch mode

Press MENU button Seven times.

The channel number flashes on the display.

Press UP or Down button until the "OF " shown on the display.

Press TALK button to exit from the Dual Watch mode.

7. Guarantee and service

The Binatone Adventurer is fully guaranteed for 12 months from the date

of purchase shown on your sales receipt. The guarantee does not cover

damage by misuse or negligence, or by excessive voltages.

Please keep your sales(till)receipt-this is your guarantee. You

should also keep the original packaging material.

When you first unpack your Binatone Adventurer, check for visible

damage. If you see any damage, don't use the handsets-return

the whole system to where you bought it .

If your Binatone Adventurer develops a fault, first check the points

above. If you can't solve the problem, return the whole system as

follows;

While the unit is under Guarantee

1 Pack up all parts of your Adventurer, using the original packaging.

Remember to include the mains adapter.

2 Return the unit to the shop where you bought it, making sure you

take your sales receipt.

3 In the unlikely event that you need to return your Adventurer to our

Repair Centre while it is under Guarantee, please send your sales

receipt with it, There will be a 5 handling charge for repair under

Guarantee.

Binatone Telecom plc operates a policy of continuous

product improvement, and so reserves the right to make

changes to the product and functions without notice.

Binatone Help Line: 0845 345 9677

Scanning Channels

When the Scan function is tuned on, the handset will continuously

scan the through all eight channels and all 38 sub-channels until it

find one on which another user is transmitting.

Press MENU and UP button at the same time.

appears on the display, and channel number change

continuously. When a signal is detected, the unit will pause.

Press UP button to continue scanning for main channel.

Press Down button to scan the Sub-channels.

Press TALK button to stop the scan and communicate.

To unlock the buttons

Press and hold the MENU button until " " disappears

from the display.

Locking the buttons

With the button locked you can transmit (Talk), receive or

monitor(MON) the current channel. But you can't change the volume

( ) or use the MENU button.

To lock the button

Press and hold the MENU button until " " appears on the

display.

Binatone Help Line: 0845 345 9677

Press UP or Down button to change the Call-Ring tone.

(5 different tones),the different Call-Ring tone can be heard

during changing.

Press TALK button to confirm your setting after you select

your desired Call-Tone.

Setting Call-Ring off

If you don't want to hear the call tone, you can set the Call-Ring

mode to OFF. In this stage, you can send the call-ring(default call-

ring number 1)to other party but the PMR you held will not sound.

Press MENU button for Four times, the unit will enter to

Call-Ring setting mode.

Press UP or Down button until display on t he LCD panel.

Press TALK button to confirm your setting.

Roger Beep ON/OFF setting

The roger Beep is a Tone which is automatically transmitted

whenever the TALK button is released. This lets other person know

that you have finished talk and you are now in receive mode.

To enable or disable the Roger Beep tone

Press the MENU button for Five times until the

flashing on the LCD screen.

Press UP or Down button to enable ("ON" will appear on the

display) or disable ("OF" will appear on the display) the

roger tone.

Press TALK button to confirm the setting.

Key tone ON/OFF setting

This feature allows the PMR unit to sound a confirmation tone

whenever keys are pressed.

To turn the Key-Tone ON or OFF

Press the MENU button Six times. The " icon flashes

on the display.

Press UP or Down button to enable (' will appear on the

LCD )or disable (' Will appear on the LCD) the key tone

feature.

Press TALK button to confirm your setting.

On '

OF '

Monitoring Two channels at once(Dual Watch)

Press MENU button for Seven times.

DCM appear on the display while "OF " is flashing.

PTT

Binatone Help Line: 0845 345 9677 Binatone Help Line: 0845 345 9677 Binatone Help Line: 0845 345 9677 Binatone Help Line: 0845 345 9677

1 2

Comments to this Manuals

No comments

Binatone ADVENTURER 100 User Manual Page 2

Comments to this Manuals